BAND SAW Table Insert-Plate 2-1/2″ (Two Pack) Aluminum DELTA / ROCKWELL *NEW*
*NEW and IMPROVED* ( Set of Two ) Solid Aluminum Band Saw Table Inserts. For: ROCKWELL / DELTA Milwaukee BAND SAWS. These inserts will fit most Delta models, and many other Brands. Measurements: 2 1/2″ Diameter X 3/32″ Thick. Replacement of the Table Plate allows for better Support, Stability and Accuracy of the piece being cut. The Narrower the Blade Slot = longer Wear, Better Support . Note-1: Do Not make the Purchase of this 2-1/2 X 3/32″ Insert without having first measured the Insert Pocket on your Bandsaw. It is your responsibility to make sure your Bandsaw accommodates a 2-1/2″ Diameter Insert. Note-2: A Metal Punch can be Used on the Edge of the Plate to Create a Bulge or Nipple on the Right or Left Hand Side of the Plate that will Lock the Plate and Keep it from Spinning. Note-3: If your Bandsaw Table Plate Cavity has a Indexing Pin. A Notch will need to be Cut in the Aluminum plate to accommodate the Pin. This can be done by a Hacksaw or the Bandsaw itself and will not hurt the blade, the plate being aluminum. It will then Stabilize the Plate and keep it from Rotation. Because of the Slight Variance of the size of the Plate Hole in the different Models of Bandsaw’s, that use this Size of Plate, there could be the need to lightly sand the edge of the Plate for the Proper Fit. Any Question’s? Please feel free to Ask.
BAND SAW Table Insert/Plate-Two Pack 2-1/2″ Aluminum -DELTA + Other Brands *New*
*NEW and IMPROVED* Set of Two Solid Aluminum Band Saw Table Inserts. For: ROCKWELL / DELTA Milwaukee BAND SAWS. These inserts will fit most Delta models, and many other Brands. Measurements: 2 1/2″ Diameter X 3/32″ Thick. Replacement of the Table Plate allows for better Support, Stability and Accuracy of the piece being cut. The Narrower the Blade Slot, the Better the Support . Note-1: Do Not make the Purchase of this 2-1/2″X 3/32″ Insert without having first measured the Insert Pocket on your Bandsaw. It is your responsibility to make sure your Bandsaw accommodates a 2-1/2″ Diameter Insert. Note-2: A Metal Punch can be Used on the Edge of the Plate to Create a Bulge or Nipple on the Right or Left Hand Side of the Plate that will Lock the Plate and Keep it from Spinning. Note-3: If your Bandsaw Table Plate Cavity has a Indexing Pin. A Notch will need to made in the Aluminum plate to accommodate the Pin. This can be done by a Hacksaw or the Bandsaw itself and will not hurt the blade, the plate being aluminum. It will then Stabilize the Plate and keep it from Rotation. Because of the Slight Variance of the size of the Plate Hole in the different Models of Bandsaw’s, that use this Size of Plate, there could be the need to lightly sand the edge of the Plate for the Proper Fit. Any Question’s? Please feel free to Ask.
BAND SAW Table Insert / Plate – Two Pack 3″ Aluminum – ROCKWELL / DELTA *NEW*
*NEW and IMPROVED* Set of Two Solid Aluminum Band Saw Table Inserts. For: ROCKWELL / DELTA Milwaukee BAND SAWS. These inserts will fit most Delta models, and many other Brands. Measurements: 3″ Diameter X 3/32″ or .090″ or 2.31 mm Thick. Replacement of the Table Plate allows for better Support, Stability and Accuracy of the piece being cut. The Narrower the Blade Slot, the Better the Support. (This Insert is Flat and has no Lip. It fits in the top portion of the Bandsaw’s insert pocket.) ( PLEASE READ ALL NOTES ) Note-1: Do Not make the Purchase of this 3″ X 3/32″ Insert without having first measured the Insert Pocket on your Bandsaw. It is your responsibility to make sure your Bandsaw accommodates a 3″ Diameter Insert.Note-2: If your Bandsaw Insert Table Cavity requires an Insert with a Nipple, a Metal Punch can be Used on the Edge of the Insert to Create a Bulge or Nipple on the Right and or Left hand Side of the Insert that will Lock the Insert in place and keep it from Spinning. Note-3: If your Bandsaw Insert Table Cavity has an Indexing Pin. A Notch will need to be made in the Aluminum Insert to accommodate the Pin. This can be done by a Hacksaw or the Bandsaw itself and will not hurt the blade, the Insert being Aluminum. It will then Stabilize the Plate and keep it from Rotation.Note-4: Because of the Slight Variance of the size of the Insert Hole in the different Models of Bandsaw’s, for this size of Insert, there could be the need to lightly sand the edge of the Insert for a Proper Fit. Any Question’s? Please feel free to Ask.