Sherline 3.1 in 4-Jaw Self-Centering Chuck 1076
Sherline 3.1 in 4-Jaw Self-Centering Chuck 1076 Sherline 3.1 in 4-Jaw Self-Centering Chuck 1076 This chuck combines the ease-of-use advantages of the 3-jaw chuck with some of the advantages of a 4-jaw chuck. It will automatically center square or round stock. (The stock must be accurately shaped for all four jaws to grip.) It will also grip thin-wall tubing in four places rather than three, which spreads out the load and allows more grip without crushing the tubing. Turning the knurled portion of the outer diameter of the chuck scrolls all four jaws in unison. Included with the chuck are two Tommy bars for tightening and loosening the chuck. The spindle thread is 3/4-16 to fit all Sherline and similar spindles. Centering accuracy on self-centering chucks is to within a few thousandths of an inch. If perfect centering accuracy is required, see the section on 4-jaw independent jaw chucks. This chuck will hold parts from 3/32 in diameter up to 1-1/2 with jaws in the normal position and up to 2-3/4 with the jaws reversed. A smaller 2.5 diameter chuck is also available as P/N 1075 Chuck Diameter: 3.1″ Jaw Capacity With jaws in normal position: 3/32″ (2mm) – 1-1/2″ (38mm) With jaws in reverse position: 3/32″ (2mm) – 2-3/4″ (70mm) Through Hole Diameter .687″ (17mm) Thread Size 3/4-16 (other thread sizes available in 2.5″ diameter) Chuck Body Material 12L14 Steel Chuck Jaws Material 12L14 Case Hardened Steel Shipping Delivery time: To keep shipping costs as low as possible we ship USPS Ground (7-10 day) Payment We accept the following payment methods: Paypal Service International Shipments: We cannot guarantee any specific delivery times.
Sherline 1030 – 3.1 in 4-Jaw Chuck
Sherline 1030 – 3.1 in 4-Jaw Chuck Sherline 1030 3.1 in 4-Jaw Chuck This larger chuck takes up no more center-to-center space than the 2.5 chuck, but it will hold larger work. It has a clamping range of from 3/32 (2 mm) up to 1-1/2 (38 mm) diameter with the jaws in the normal position. With the jaws in the reversed position, work up to 2-3/4 (70 mm) can be gripped. The hole through the chuck is .687 (17 mm). A hex key (provided) is used to tighten each jaw individually. A groove is machined around the base of the chuck so that angle clamps can be used to mount it to the table of a mill as a holding fixture. The chuck has a 3/4-16 thread to fit Sherlines spindle and other machines using that thread. Shipping Delivery time: To keep shipping costs as low as possible we ship USPS Ground (7-10 day) Payment We accept the following payment methods: Paypal Service International Shipments: We cannot guarantee any specific delivery times.
Sherline 1030 – 3.1 in 4-Jaw Chuck New in Box
Sherline 1030 – 3.1 in 4-Jaw Chuck. This larger chuck takes up no more center-to-center space than the 2.5″ chuck, but it will hold larger work. With the jaws in the reversed position, work up to 2-3/4″ (70 mm) can be gripped.
Sherline Pair Carbide Insert Holder 55 Degree (1 Left and Right Pair) 2258
They are available individually as a right-hand holder (P/N 2256) or a left-hand holder (P/N 2257). The pair of RH and LH is P/N 2258. The 35° offset angle of the tip makes it easier to accomplish certain cuts.
Sherline Carbide Tip RH 80° 3/8 Inch Boring Bar w/2 Flats
Sherline added a second flat to their standard boring bars so they could be held with the insert face up or face down. The 80° RH boring tool will fit into a 3/4″ starting hole. The 3-1/4″ long holder can bore a hole a little over 2″ deep with two fastening screws tightened on it.
Sherline 5/16 Inch Minimum 1.5 Inch Max Boring Tool 3064
Sherline 5/16 Inch Minimum 1.5 Inch Max Boring Tool 3064 Sherline 5/16 Inch Minimum 1.5 Inch Max Boring Tool 3064 5/16 Inch Minimum 1.5 Inch Max Boring Tool These high-speed steel cutting tools are designed for use with the Sherline boring head. They have a 3/8 (9.5mm) diameter shank. P/N 3064 is also 5/16 minimum but has a longer 1.5 reach. If desired, they can easily be ground down to work in a smaller hole. The shank has a flat ground on one side that is for the set screw of the boring head to tighten against. Shipping Delivery time: To keep shipping costs as low as possible we ship USPS Ground (7-10 day) Payment We accept the following payment methods: Paypal Service International Shipments: We cannot guarantee any specific delivery times.
Sherline 70 Deg. 35TPI 55T Straight Knurl Pair 3621
Sherline 70 Deg. 35TPI 55T Straight Knurl Pair 3621. 35TPI 55T Straight Knurl Pair. TOOTH PATTERN: STRAIGHT. HARDNESS: 58 to 60 RC. NORMAL CIRCULAR TPI: 40. SERIES: EP. TOOL MATERIAL: High Speed Steel.
Sherline 5/32 Inch End Mill dia., 3/8 Inch cut, 1-17/32 Inch 7204
Sherline 5/32 Inch End Mill dia., 3/8 Inch cut, 1-17/32 Inch 7204 Sherline 5/32 Inch End Mill dia., 3/8 Inch cut, 1-17/32 Inch 7204 Sherline 5/32 Inch End Mill (ball nose) SIZE: 5/32 NO. OF FLUTES: 3 LENGTH OF CUT: 3/8″ SHANK DIAMETER: 1/4″ TOOL MATERIAL: High Speed Steel FINISH COATING: Bright Finish SINGLE OR DOUBLE END: Single OVERALL LENGTH: 1-17/32″ CENTER CUTTING: Yes CUTTING DIRECTION: Right Hand END TYPE: Ball Single End FLUTE SHAPE: Helix FLUTE LENGTH: 3/8″ HARDNESS: 58 to 60 RC Shipping Delivery time: To keep shipping costs as low as possible we ship USPS Ground (7-10 day) Payment We accept the following payment methods: Paypal Service International Shipments: We cannot guarantee any specific delivery times.
Sherline 1015 – 5/32 Inch Drill Chuck with #0 Morse Arbor
Sherline 1015 – 5/32 Inch Drill Chuck with #0 Morse Arbor Sherline 1015 5/32 Inch Drill Chuck with #0 Morse Arbor ***The P/N 1015 Chuck is identical in capacity to the 1010 chuck shown except that a #0 Morse arbor has been pressed into the Jacobs taper in the back of the chuck. It is used in the tailstock and does not require a drawbolt*** We supply a #0 Morse arbor for use in the tailstock for center drilling. The chucks are also available with a #1 Morse arbor and drawbolt for use in the headstock for drilling on the lathe or mill. They are available in 5/32, 1/4 and 3/8 sizes. Runout is .003 or less. If runout of less than this amount is required, collets should be used to hole the drill rather than a chuck.The P/N 1015 Chuck is identical in capacity to the 1010 chuck. It is used in the tailstock and does not require a drawbolt. NOTE: Because the arbor is pressed into the chuck, it is not interchangeable from chuck to chuck. A separate chuck must be purchased for #0 and #1 Morse use Shipping Delivery time: To keep shipping costs as low as possible we ship USPS Ground (7-10 day) Payment We accept the following payment methods: Paypal Service International Shipments: We cannot guarantee any specific delivery times.
Sherline 1010 – 5/32 Inch Drill Chuck with #1 Morse Arbor
Sherline 1010 – 5/32 Inch Drill Chuck with #1 Morse Arbor Sherline 1010 5/32 Inch Drill Chuck with #1 Morse Arbor Sherlines drill chucks are available in 5/32, 1/4 and 3/8 sizes. Runout is .003 or less. If runout of less than this amount is required, collets should be used to hole the drill rather than a chuck. The 5/32 chuck holds drills from 5/32 (4mm) down to #80 (.0135 or .343mm). We have pressed a special arbor that provides either a #1 Morse taper to fit into the Sherline headstock (P/N 1010) or a #0 Morse taper to fit the tailstock (See P/N 1015). A chuck key plus a drawbolt and washer are included with P/N 1010 to secure the chuck in position. These chucks are useful for holding very small drills and their shorter length provides an increase of about 1/2 in working space between centers compared to the 1/4 drill chuck. Shipping Delivery time: To keep shipping costs as low as possible we ship USPS Ground (7-10 day) Payment We accept the following payment methods: Paypal Service International Shipments: We cannot guarantee any specific delivery times.